TIPS ABOUT HOW TO Extend Smok Pen Recharge Time


TIPS ABOUT HOW TO Extend Smok Pen Recharge Time

The Smok Pen is a new pen that was created by two guys in California. They wished to create a cool writing instrument that appeared as if a genuine pen but had the opportunity to smoke a hookah. They named their product the Smok Valve and the Smok Pen. The Smok Valve has taken the market by storm.

The Smok Pen includes a built quality that’s just great. I found that even though it is an electronic pen the build quality is just as good as the pens that I’ve reviewed. It is because of how they made the most notable cap. You don’t have to be worried about the cap cracking or breaking on you Smok Valve Pen.

The two biggest differences that separate the Smok Valve from other pens is the shape of the coils and just how that they are built. Generally the coil on a Smok Pen is larger than on other pens. I believe that they did this on purpose, to make the pen feel bigger.

Invest vapinger.com the a look at a Smok Pen, you will notice that your body of the pen is round and not smooth like other pens. On the back of the pen there is a little tab that houses the coil. Once you press on the tab you can easily turn the heating element on / off. I must say i liked this feature since it allows me to use the Smok Pen 22 whenever I feel like smoking.

To use the Smok Pen you have to keep carefully the heat button pressed. Once the button is pressed, the heating element will begin to warm up. Once it reaches the appropriate temperature it is possible to switch off the heating element. Smok recommends using a 22mm tank. I prefer a larger tank, but that’s just me.

Once you put your Smok Pen into the tank you will notice a indicator light seriously. The indicator light will stay green if you don’t put your Smok Pen into the Smok Pen charger. Once your Smok Pen has entered the charger the indicator light will turn red. It is very important always put your pen in to the charger before you apply the e-liquids to the coil heads. It is also important to do that before putting your e-liquids into the coil heads.

After you have completed this step, it is best to check to see when you are at the right temperature for the coils to fire. Or even then you should turn the energy off and try again. Should you be still not satisfied with your Smok Pen i quickly suggest you take it set for some troubleshooting. This is what I’d call the “troubleshooting process” because sometimes things just do not work as they should. I would recommend that you perform the following two steps, then go on and check the Smok Pen to see if it still has the electronic charging port.

Prior to going any further you should remove the battery from your pen and unscrew the magnetic cap. You should then take away the plastic sleeve that holds the sub-ohm. There is a wire that runs through the Smok’s body that is green in color. You should loosen this wire using pliers. After you have loosened this wire you can then access the sub-ohm. You need to then take away the wire from the Smok’s body and carefully insert it into the Smok pen’s electrical port, being careful to not touch any of the coils.

When you have placed the sub-ohm tank in to the pen you should then place the rest of the components like the wattage, the batteries and the heating element in to the included microwaveable microwave oven. Turn on the power and follow the on screen instructions. You need to place the pen’s battery in to the microwave and activate the setting. You need to then wait approximately 30 seconds before turning it cool off. When you initially put the pen in to the microwave the electronic reading will show a low voltage protection setting. If this setting will not automatically get set you then should follow the on screen instructions.

After the Smok Pen has already reached the temperature that it needs to reach you need to then connect both wires to the negative and positive on the positive post on the Smok unit. You need to then connect another end of the battery to the negative post on the negative side of the Smok unit. The final step would be to connect the positive cable to underneath of the Smok’s on / off switch.

After all of the components have been placed into the pen, you should turn the energy on. After the first test run, you should be able to start to see the battery life indicator light come on. If you don’t see any sign of life from the Smok Pen, you need to remove the battery from the pen and then replace it with a fresh one. For your convenience gleam green light which can be pressed to be able to confirm the battery charging status. Once you have done these things and you also do not see the green light indicating charging, you should replace the battery.

Posted in Uncategorized